Victron Energy Quattro 48/10000/120-230V VE.Bus
- Quattro 48/10000/140-100/100 120V VE.Bus
- Quattro 48/10000/140-100/100 230V VE.Bus
The Quattro 48/10000/140-100/100 is a combination of a 48V 8000W sine wave inverter, a powerful battery charger and a transfer switch. It has two AC outputs and two AC inputs, each of which is equip-ped with a 100A transfer switch. It can be connected to two independently operating power sources, with the Quattro automatically connecting to the active power source.
The Quattro is designed in such a way that the main entrance takes over the overall supply of the connected devices in the event of a power failure etc. This guarantees an uninterruptible power supply because the Quattro takes over the power supply in a fraction of a second, so that a failure of electrical devices such as a computer is not registered. The second output only provides power if AC power is available at one of the Quattro's inputs.
Charger
The permanently integrated battery charger delivers an impressive 140A, so that even large batteries can be charged. With the built-in 48V sine voltage converter, the battery current is converted into 230V AC. Due to the sine wave, the connection to sensitive electronic devices is also suitable. Each AC input has a 100A transfer switch. This also ensures a multitude of applications in grid-connected operation.
Features of the Quattro 48/10000 / 140-100 / 100
- 8000W continuous power and 20000W peak power, for 48V battery voltage
- Device combination of inverter with transfer switch and 140A battery charger
- delivers the purest 230V sine voltage and a clean 50Hz frequency
- 2 AC inputs with integrated transfer switch / 2 x 100 A maximum switchable current
- 2 AC outputs + 1x additional output which only allows the current to pass to the consumer when the - AC input is active.
- VE.Bus communication port provides extensive options for networking, system integration,
configuration and control of the Multiplus devices from Victron.
- supports three-phase operation (3 identical units of the same model required)
- Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, thereby
significantly increasing system performance if necessary
- 2x COM ports are available in addition to the VE.Bus port, so there are virtually no limits to system
integration
- PowerControl function enables working with limited generator power as well as limited shore or grid
current
- PowerAssist function enables "performance increase" of generators and shore connection support if
necessary
- Can be used as a UPS solution for uninterruptible power supply thanks to the integrated 100A
transfer switch
- Can be used for grid-connected self-consumption systems that only draw power from the grid
operator if the battery capacity is no longer sufficient or other programmable events have occurred
3 separately programmable relays
- compatible with numerous Victron control and display panels
- very high efficiency and low self-consumption
Parallel connection and 3-phase configuration
The Quattro enables up to six devices to be connected in parallel, so that, for example, six 48/10000/140 units generate an output of 54 kW / 60 kVA or 840 A charging current. Three units can be switched in a 3-phase configuration. You can even connect up to six sets of three devices in parallel.
PowerControl
The Quattro integrates a very powerful battery charger. It draws a lot of current from the generator or shore power supply, the maximum output of which can be set with the Multi Control control panel. The Quattro even takes other connected electronic devices into account and only uses the electricity that is "left" for charging. This prevents the generator or shore power connection from being overloaded.
PowerAssist
The PowerAssist with the PowerControl enables the Quattro to support alternative sources that are too weak. At peak loads, the Quattro ensures that weak power output is bridged using battery power.
BackUp system
The Quattro can be used with off-grid and grid-connected PV systems as well as with other alternative energy systems. Software to detect a power failure is available.
Simple system configuration
If settings on a single device need to be changed, this can be done within a few minutes using a DIP switch setting procedure.
Parallel and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.
Simple system configuration
If settings on a single device need to be changed, this can be done within a few minutes using a DIP switch setting procedure.
Parallel and three-phase systems can be configured with the VE.Bus Quick Configure and VE.Bus System Configurator software.
Monitoring options and control
The Quattro can be monitored and controlled both on site and remotely, among others. with battery monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232) or Victron Ethernet Remote, Victron Global Remote and the Color Control Panel for the Remote control.
Remote configuration
If systems with a color control panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.
Delivery time approx.:
1 - 2 Workdays
(DE - int. shipments may differ)
